How are shingles ordered? – [Glossary]

How are shingles ordered?

Determine the number of shingles to order for starters by measuring the length of the eaves and rakes, then round up to the nearest foot and divide by three (the length of a shingle).

How many shingles are in a bundle of roofing?

Standard size shingles (12 inches by 36 inches): 29 shingles per bundle. Asphalt 3-tab roof shingles: 26 shingles per bundle.

How many square feet does 1 bundle of shingles cover?

Calculating the number of bundles, you need is simple if you are using shingles that come three bundles to a square. Each bundle covers 33.3 sq. ft. of roof area—which is close enough to the 32 sq.

How many shingles do I need for 500 square feet?

How Many Bundles of Shingles Will You Need. The average bundle of shingles covers 33.3 ft2, so three bundles of shingles are needed per square.

How many squares are in a pallet of shingles?

33 square feet is the size of each bundle. A pallet of shingles can hold up to 42 bundles. The pallet weighs in between 2,100 and 3,350 pounds.

Is it better to hand nail shingles?

Hand Nailing Shingles is better than using a Nail Gun or a Pneumatic Nailer because it allows the roofers to feel the nail placement and ensure optimal installation. However, most manufacturers claim that either method is a viable option.

Should roofing nails go through the sheathing?

It is crucial that roofing nails of the correct length were used to secure the shingles. The sharp tip of the roofing nail should pass through and extend approximately 3/8-inch past the underside of the roof sheathing.

What is my roof pitch?

The angle, or pitch, of a roof is calculated by the number of inches it rises vertically for every 12 inches it extends horizontally. For example, a roof that rises 6 inches for every 12 inches of horizontal run has a 6-in-12 pitch.

How much roofing do I need?

To estimate how many shingles you’ll need, first estimate the total square footage of your roof’s surface. To do this, measure the length and width of each plane on the roof, including dormers. Then, multiply length x width to get the square footage of each plane.

How are shingles sold?

How Shingle Quantities are Measured. Roof shingles are sold by both the bundle and by the square. A square of shingles is the quantity needed to cover 100 sq. ft.

How many squares of shingles do I need for a 1500 square foot house?

For a 1500 square foot house, you will need approximately 19 squares or 57 bundles or 1653 pieces of 3-tab standard-sized shingles (12 inch by 36 inch) when overhangs is 1 feet and roof slope is 4/12.

How many sq feet does a bundle of shingles cover?

Standard shingles are 12 by 36 inches and come 29 to a package. Most shingles come 3 bundles to a square — which is equal to 100 square feet. So, each bundle provides about 33 square feet of coverage.

How many squares is a typical roof?

The roofs are measured in squares. 100 square feet is equivalent to a square in roofing terms. The roof of the average home is 3000 square feet.

Do you have to remove plastic strip on shingles?

Because the cellophane strips have no effect on the performance of asphalt shingles, it’s fine to leave them in place as you install the shingles. In fact, the effort to remove them is unnecessary and just adds an extra step for the contractor.

How do you keep shingles straight?

e shingles aligned vertically and horizontally. A chalk line can keep your line straight over long distances and large areas. A chalk line can help eliminate short exposures, waviness and additional antithetical issues. The first step in roofing is always to install the underlayment and any additional weather shields.

Do you hammer shingles?

Most do-it-yourselfers will purchase their shingles and never think about how to fasten them to the roof. Most think that nailing the composition shingle with a hammer is the only way.

How far do shingles overhang drip edge?

Asphalt shingles should overhang the exterior edge of the drip edge by ¼ to ¾-inch. Check local building code for drip edge requirements prior to the start of your roofing project.

What thickness plywood should you use for a roof?

Most Common Thickness For rafters spaced 20 or more inches apart, 1/2- or 5/8-inch plywood is recommended. The most common rafter spacing is 24 inches, and 5/8-inch plywood is recommended for that. It will support roof loads for most situations and is the standard for most roof applications.

How long is a rafters on a 4/12 pitch?

4/12 or “4 in 12” roof pitch or slope, generally roof rafter length will be 15.81 feet or 4.82m long for 30 feet span. It will goes up when span is increases or will goes down if span is decreases. Note that this is not the actual length of the roof rafter. If you plan to have overhang, etc.

How many squares of shingles do I need for a 1800 square foot house?

A roofing square is equal to 100 feet on your roof. If your roof measures at 1800 square feet, you would need 18 squares of shingles to cover your roof.